Network for PowerBlock fans
z3r0co01's Page
Latest Activity
Should be the same. The '01 just doesn't say "high output". Information I've found says they ran the same from 1996-2001. They should swap out just fine.
Cherokee Classic engines through the years:
* 1985-1987 4.0L I6 "Power Tech" - 177 hp @ 4750 ...
I would disconect the neg on your batt let your computer re-set and see if the code comes back up ... the water could have hit something to give u a false error code
so i got this 01 jeep cherokee for 300 bucks its got a blown motor i have a 97 with a wrecked body would i be able to drop my 97 4.0l high output str.6 into the 01 jeep ... it seems to have the same motor its just not high output its a 4.0 str.6 i...
its almost fixed ... all the bushings and things where shot -- ball joints where toast and much more im working my way thru all of it lol but in my mind this thing is still a good buy, i love this straight 6 --- 4.0 high output engine my next ques...
Jeep suspension is very simple to work on and fix , the parts are not as expensive as some vehicles, check out some Jeep sites, jeepininin.com, jeepforum.com, greatlakesxj.com, and I am a member of all these sites and the write ups are very well d...
well i had a jeep that had that problem when you got to about 35mph it would shemmy left to right and i replaced every thing but the drag link and it came to pass that the drag link was the promblem so give that a check
check the tie rods, stabilizer, tires (busted belt), if the axle was bent id say you would be doing a lot more than shaking going down the road. if the leafs are shot a junkyard should have decent springs for doing what you need to do. might also ...
did it fix it?
if its not providing the support needed for your axel it will make your ride hell. replace this and your rims --> done, then you should be back to a better cruz.
if uve seen T4 thats what probly happend to your jeep... still wasnt a bad buy. but ...
Okay so i found out the thing is a control arm i can get one for 60 bucks ... now the question is, would this be part of my death wobble and would i be able to bend them arms with a wood block and a hammer also my rims where bent this added to my ...
HELLO I THINK THIS IS CALLED THE KING PIN . CHECK OUT QUADRATEC THEY SELL JEEP PARTS AND THEY ARE NOT PRICED TOO HIGH LET ME KNOW IF THIS IS CORRECT. TAKE CARE.
I like the 4WD suspension packages they preform well and dont cost a arm and a leg u can get a nice kit for around 650.00 try this site http://www.4wd.com/jeep-parts.aspx?cid=17&jeep-sid=357&plID=60 its a place to start ... let me know if that helps
5" for 600 bux isnt bad. id take it. make sure its a fit and comes with the bushings and crap. as for the pick my jeep dose not have one of thoughs but my best guess is a rocker arm of some sort sence it conects stright to the axel and looks prett...
this is the thing im talking about
i dont mess with the new ones but with the discription it sounds like a sway bar or your tie rod. if the guy riped out the exoust its and made the death wobble it sounds like this idiot tried to clear something hard heavy and solid he definatly sh...
Comment Wall (1 comment)
- At 12:24am on June 24, 2009,
Grant said…
- that control arm that you are displaying may be a problem if the bushings on either end are warn. however I think that you should be checking your joints. as someone else all ready staighted. If any are loose ... even a little they should be replaced. have a reliable shop look at the alignment so as you know what is needed!
your control arms hold the axle front to back. the tie rods hold the wheels in alignment called toe! ball joints hold the spindle that the wheel is fastened to in alingment with the road. the track bar holds the axle centered under the truck. all of these parts work together to keep the vehical straight down the road. be sure they are good!!!!
Profile Information
- First Name
- Steve
© 2009 Created by Gearhead
