myPOWERBLOCK

Network for PowerNation fans

Goose
  • Male
  • Ontario
  • Canada
Share on Facebook
Share

Goose's Friends

  • Stormy Dee Sims
  • RileysPerformance
  • Tiffani Whitehead
  • Brian Williams
  • Alice Cornelios
  • Darren Young
  • RONALD ORZEL
  • Melissa A. LadyWolf Fraley
  • Heidi Michelle Muller
  • Chuck Schauwecker
  • Jamie Perna
  • Daniel Gamelin
  • Scott Summerson
  • emma marie
  • Edward R Schrader

Goose's Groups

 

Goose's Page

Latest Activity

Goose commented on Gearhead's group DODGE TRUCKS
"Hello Jeremy They should be the same transmission. The difference between the Lamamie and the sport was trim package from what I can remember. Your best bet if you can is to get the Vin # for both trucks if you can and call yor local dealer and ask…"
Feb 4, 2015
Goose commented on Gearhead's group DODGE TRUCKS
"No problem Glad to hear it was easy"
Jun 4, 2014
Goose commented on Gearhead's group DODGE TRUCKS
"From what I can remember you can just jack it up at the frame and the shock will hold the lower control arm and the tension from the torsion bar. But I would put the jack under the lower control arm just to be safe. Best of luck"
May 22, 2014
Goose commented on Gearhead's group DODGE TRUCKS
"If I am correct the upper ball joint should be the h*** control arm assembly so you would need to get the control arm and replace the assembly. And you should get an alignment after that. Hope that helps"
May 21, 2014
Goose commented on Gearhead's group DODGE TRUCKS
"Hey Scott You can always try your local dealer to to see what the price is. It's just a phone call and it may not be that bad"
Mar 6, 2014
Goose commented on Gearhead's group DODGE TRUCKS
"Hey Scott you can try LMC Trucks I know some parts from them are cheap other try your local wrecking yards"
Mar 6, 2014
Goose commented on Gearhead's group XTREME 4X4
"Anthony yes anything can be done depending on your skill level or how deep your pockets are. Best of luck with the project"
Feb 27, 2014
Goose commented on Gearhead's group DODGE TRUCKS
"Hey Scott did the brakes work when you pulled the trailer with the van? If so check your trailer brake control unit fuse then the unit itself. Sounds silly but make sure the unit is adjusted properly cause I know I bump mine with my leg from time to…"
Feb 2, 2014
Goose commented on Gearhead's group DODGE TRUCKS
"Well I know on my 04 Ram I have a 7 pin in the rear bumper and a 4 pin under the rear bumper near the receiver I have seen cases of that 4 pin connector getting corroded and causing the trailer lights to not work or to do some funny things. So I…"
Feb 2, 2014
Goose commented on Gearhead's group DODGE TRUCKS
"Hey Scott are you sure it's the fuse box that is messing up your trailer wiring. What is happening with your trailer lights?"
Feb 2, 2014
Goose replied to Barry A. Rice's discussion Hinge repair in the group DIY projects
"The only thing I can say to try is to search the internet. Best thing is to type in 1936 Ford Coupe door hinge you will have to search tr pages that come up and you will find something"
Jan 28, 2014
Goose commented on Gearhead's group DODGE TRUCKS
"Cool thanks Jamie"
Dec 16, 2013
Goose posted a photo
Dec 16, 2013
Goose commented on Gearhead's group DODGE TRUCKS
"Does anyone know of a lift kit for a 2003 Dodge Durango"
Dec 14, 2013
Goose commented on Gearhead's group TRUCKS!
"Does anyone know of a lift kit for a 2003 Dodge Durango looking for a suspension lift or a body lift either would do"
Dec 14, 2013
Goose commented on Gearhead's group XTREME 4X4
"Has anyone lifted a 2003 Dodge Durango or know of any lifts for them can not find any have been look for a few months now can find a body lift but want a suspension lift looking for a 4 inch lift. From I can can find the rack is the problem if…"
Dec 11, 2013

Profile Information

First Name
Dennis

Goose's Photos

Loading…
  • Add Photos
  • View All

Comment Wall (15 comments)

You need to be a member of myPOWERBLOCK to add comments!

Join myPOWERBLOCK

At 7:33am on February 2, 2013, Melissa A. LadyWolf Fraley said…

Thanks for the add. and the info...I will look at the messages... the difference I found out was the 1st type of ball joint is fixed, cant be adjusted. The other one, is the one I need, it adjusts the Camber and toe. These are the ones I need. Going to have them replaced today. Then I will work on the other recommeded changes.. to prevent this from happening again later on down the road... Thanks again, for the info.. and invite...

At 11:11am on September 23, 2012, Daniel Gamelin said…

hey thxs for the request!!

At 7:12am on June 29, 2012, Jeff said…

thanks for answering, yes i do have a trans cooler. this time i am going to put a trans guage in the truck.   thanks,jeff

At 7:17pm on May 1, 2012, Mike the Goofy 1 said…

I got the clutch and thanx for all the info u gave me, it just took alot of time and new flywheel

 

At 10:05am on April 29, 2012, Mike the Goofy 1 said…

Hello Goose I am still haven a little problem with bleeding the clutch to get it not to grind i reverse also hard to get into gear so I pulled the trans back and pumped the slave and then put together and now i got better but still not going  to pump al the way up I can get it in gear but I have to pump it alot so what do I do??? help please 

At 11:48am on February 26, 2012, Vicky Peterson said…

It really is cool to see how helpful you are to people! This site is great. especially for a girl w 3 trucks! Most think I'm crazy but not here.. :)

 

At 1:40pm on October 1, 2011, Michael Cates said…
If i learn more i will pass the info on. Research is a hobby of mine.
At 9:11am on June 20, 2011, Gena Rose Matthews said…

Thanks for accepting me.

 

At 12:48am on March 17, 2011, Kimberly & Jason Burson said…
How's it going Goose, Thanks for adding me as your friend.
At 8:12am on March 13, 2011, Teresa Goodrich said…

Four doors are better than two! Thanks for the add. :)

 
 
 

© 2017   Created by Gearhead.   Powered by

Badges  |  Report an Issue  |  Terms of Service